Customer Feedback

06/09/24 - One10T + Big Baby 3 - USA

BB3’s little brother, One10T has arrived! This little guy is small but mighty. Only 4 weeks from ordering and shipping to CA. I’m so happy with this. Thanks BF team! p.s. I was bored last night and hooked up my rig to the tv and watched a horror movie. It sounded so real I’m lucky the neighbours didn’t call the police

Jeremy

14/10/23 - Big Baby 2 - USA

I have the BB2 which I love. What’s the difference between BB2 and BB3?

Chris

-------------------------------------------

Hi Chris,

Here's a rundown of the 3 vs 2 differences: https://barefacedaudio.com/pages/top-secret

Glad you're loving your BB2!

Best regards,

Alex

10/10/24 - Big Baby 3 - UK

Loving my big baby 3 still and will be looking at some of your AVD guitar cabs next year :)

Shane

10/10/24 - Big Twin 3 + Big Baby 3 - USA

I have a BT3 and a BB3 and love them both ! Would definitely  have paid 5-600 more per cab if I had to! Thank y'all and God speed!

Corey

11/10/24 - Big Baby 3 - USA

I’ve been thrilled with my BB3 I acquired earlier this year. But the 10CR is so compelling, I’m planning a Three 10 order. Not ready now, but expect an order in early 2025 

Al

10/10/24 - Big Baby 2 - UK

Hi! I’ve been the proud owner of Big Twin 2 (Gen 3) for many years now.

Always loved the transparency of the cab with my Genz Benz & Darkglass heads. I’ve recently moved over to a Neural DSP Quad Cortex and I’ve found it a struggle to get a tone I’m happy with thus far. Being an FRFR cab (though no ordinary FRFR ofc), I expected using a modelled head & cab IR I’m familiar with, it to be an instant hit, but I’m finding that the bass response is overwhelming, almost head splitting where I have to turn it down where It gets lost in a rehearsal mix, or it’s too spiky in the high end using overdrives.

I can’t find the balance! I’m happy with the tone in IEMS in general so I’m a little lost! Do you have any advice for optimising the Quad Cortex for the BT2? EQ or general tips for modellers with the Big Twin series?

Thank you so much for any advice you may have!

Tom

---------------------------------------

Hi Tom,

There's a few things it could be - if the cab is in the corner of a room with solid walls then you get a load of extra lows. If the HF control is all the way up then you may want to back it off a bit. The quality of IRs is very variable (the more I learn about them, the more incomplete I realise they are). Or is there any EQ in the signal chain going to the cab? In a normal half-space environment (on the ground, walls a long way away) the response of the BT2 is pretty damned flat until it rolls off the in the lows and highs - no peaks or dips of significance. From our experimentation with guitar FRFR cabs, we've found that it's rarely plug and play, it takes quite some work to get it all sorted.

Best regards,

Alex

11/09/24 - Big Baby 3 - USA

I was just curious why it has the two speakon/combi sockets? Is it just in case one fails for some reason, or is there some else to it?

I love my Big Baby 3! I'm already craving another purchase lol

Great work!

Rob

----------------------------------

Hi Rob,

Glad you're enjoying the cab!

Check this link out here - https://barefacedaudio.com/pages/why-two-inputs-why-not-normal-1-4?_pos=1&_sid=d1963d49b&_ss=r

Hopefully that answers your question.

Alex

06/10/24 - Big Twin 3 + Big Baby 3 - USA

Quick question: do I have anything to worry about hooking up the Big Twin 3 and the Big Baby 3 together to my Bergantino Forte HP 2?

I’ve done it twice for outside gigs with no front of house support and it sounded great. I set my amp at 2 ohms. But a lot of money between those three pieces of gear so I don’t wanna burn anything up.

Corey

--------------------------------------

Hi Corey,

That should be fine - set the amp to 2 ohms and each 12XN will get a third of the amp's power.

Best regards,

Alex

09/09/24 - Big Baby 2 + 3 - UK

Hi Alex, this is an odd question but, I have a Big Baby II. I’m getting a PA and have been advised that I will still need a sub even with 15” tops. I use the BB with a Crown 1000w PA amp, normally, bridged. Will I kill my cab if I use the amp and cab as a sub, for now?

Thanks. That cab is pretty damned awesome so don’t want to hurt it.

Adrian

----------------------------------------------

Hi Adrian,

As long as the cab is running clean then it'll be fine - the 12XN is designed to distort quite a lot before it blows (unless you're putting in a particularly unusual signal). What are your crossover and limiter settings going to be?

Best regards,

Alex

----------------------------------------------

25/09/24 - Big Baby 2 + 3 / One10 / Super Midget - Norway

Hi,

I need a cover for a Big Baby 2 (Not the current BB3 model). Do you still have these? If so, what will it cost? I live in Oslo, Norway.

I also own a One10 and a Super Midget that I am very happy with!

Kind regards,

Bjørnar

--------------------------------------------

Hi Bjønar,

I'm sorry, we're all out of those covers now. We might be able to get one made for you if you wish?

Glad you're enjoying the One10 and SM!

Kind regards,

Isaac

19/09/24 - Big Baby 3 - Taiwan

The BB3 with its tweeter fully on is just such a joy to play through. Super happy.

Thanks a lot for your help!

Jay

19/08/24 - Big Baby 3 - UK

I'm liking the BB3s very much. I love being able to pick them up with one hand, and the fact that they are half the weight of my Pearson/Beyma cabs. They bring a bit more heft to the bottom end of my sound, which I also like. I'm looking forward playing more gigs with them.

Richard